Stationary Source Surveillance for Large Air Quality Control Regions in Nonurban Areas

Increased energy processing activity in the north has resulted in a demand for measured data on plume dispersion that is relevant to this particular region. The north was, therefore, selected for study in a comprehensive government/Industry research program. The objective of these studies was to assess the behaviour of plumes in various geographic areas In Canada. The program utilizes airborne and automobile-mounted probes to determine SO₂ and temperature profiles within stock-emitted plumes as well as meteorological data on local atmospheric structure. The data are then analyzed numerically to obtain plume axis elevations and standard deviations of spread and these results are compared to accepted predictive methods. Good agreement with the analysis of Briggs was observed for predicting the location of the plume axis In neutral conditions; some deviations were noted in stable conditions. Values of the measured product ( σay-σ;z) were generally larger than those of Pasquill, particularly for those values close to the source. A difference between the measured values of (σ;y-σ;z) in fall and winter was observed in stable conditions.     

Letters to The Editor

Abstract

Since 1990, basic knowledge of the “chemical climate” of fine particles, has greatly improved from Junge’s compilation from the 1960s. A worldwide baseline distribution of fine particle concentrations on a synoptic scale of approximately 1000 km can be estimated at least qualitatively from measurements. A geographical distribution of fine particle characteristics is deduced from a synthesis of a variety of disparate data collected at ground level on all continents, especially in the northern hemisphere. On the average, the regional mass concentrations range from 1 to 80 μg/m³, with the highest concentrations in regions of high population density and industrialization. Fine particles by mass on a continental and hemispheric spatial scale are generally dominated by non-sea salt sulfate (0.2 to ～20 μg/m³, or ～25%) and organic carbon (0.2->10 μg/m³, or ～25%), with lesser contributions of ammonium, nitrate, elemental carbon, and elements found in sea salt or soil dust. The crustal and trace metal elements contribute a varied amount to fine particle mass depending on location, with a larger contribution in marine conditions or during certain events such as dust storms or volcanic disturbances. The average distribution of mass concentration and major components depends on the proximity to areal aggregations of sources, most of which are continental in origin, with contributions from sea salt emissions in the marine environment. The highest concentrations generally are within or near very large population and industrial centers, especially in Asia, including parts of China and India, as well as North America and Europe. Natural sources of blowing dust, sea salt, and wildfires contribute to large, intermittent spatial-scale particle loadings beyond these ranges. A sampling of 10 megacities illustrates a range of characteristic particle composition, dependent on local and regional sources. Long-range transport of pollution from spatially aggregated sources over hundreds of kilometers creates persistent regional- and continental-scale gradients of mass concentration, sulfate, and carbon species especially in the northern hemisphere. Data are sparse in the southern hemisphere, especially beyond 45° S, but are generally very low in mass concentrations.     

Advantages of Geographically Weighted Regression for Modeling Benthic Substrate in Two Greater Yellowstone Ecosystem Streams

Stream habitat assessments are commonplace in fish management, and often involve nonspatial analysis methods for quantifying or predicting habitat, such as ordinary least squares regression (OLS). Spatial relationships, however, often exist among stream habitat variables. For example, water depth, water velocity, and benthic substrate sizes within streams are often spatially correlated and may exhibit spatial nonstationarity or inconsistency in geographic space. Thus, analysis methods should address spatial relationships within habitat datasets. In this study, OLS and a recently developed method, geographically weighted regression (GWR), were used to model benthic substrate from water depth and water velocity data at two stream sites within the Greater Yellowstone Ecosystem. For data collection, each site was represented by a grid of 0.1 m² cells, where actual values of water depth, water velocity, and benthic substrate class were measured for each cell. Accuracies of regressed substrate class data by OLS and GWR methods were calculated by comparing maps, parameter estimates, and determination coefficient r ². For analysis of data from both sites, Akaike’s Information Criterion corrected for sample size indicated the best approximating model for the data resulted from GWR and not from OLS. Adjusted r ² values also supported GWR as a better approach than OLS for prediction of substrate. This study supports GWR (a spatial analysis approach) over nonspatial OLS methods for prediction of habitat for stream habitat assessments.     

Chromium speciation in river sediment pore water contaminated by tannery effluent

Cr(VI) is far more soluble and toxic than Cr(III). Sediment pore water was investigated in a river adjacent to the property of a large former tannery, into which Cr-contaminated effluent was discharged over a 55-year period, and where extremely high Cr concentrations have been found in the sediments. Dialysis cells, or peepers, were used to generate depth profiles of Cr concentration in sediment pore water. Samples were analyzed for total Cr using inductively coupled plasma-mass spectrometry (ICP-MS) and for Cr species using high performance liquid chromatography (HPLC)-ICP-MS. The results show an absence of Cr(VI) in all samples. Furthermore, incomplete recovery of Cr(VI) added to the samples collected at the locations with highest sediment Cr concentrations indicate strong reducing conditions at those locations, which are not conducive to the presence of Cr(VI).     

Application of a combined measurement and modeling method to quantify windblown dust emissions from the exposed playa at Mono Lake, California

Particulate matter < or =10 microm (PM10) emissions due to wind erosion can vary dramatically with changing surface conditions. Crust formation, mechanical disturbance, soil texture, moisture, and chemical content of the soil can affect the amount of dust emitted during a wind event. A refined method of quantifying windblown dust emissions was applied at Mono Lake, CA, to account for changing surface conditions. This method used a combination of real-time sand flux monitoring, ambient PM10 monitoring, and dispersion modeling to estimate dust emissions and their downwind impact. The method identified periods with high emissions and periods when the surface was stable (no sand flux), even though winds may have been high. A network of 25 Cox sand catchers (CSCs) was used to measure the mass of saltating particles to estimate sand flux rates across a 2-km2 area. Two electronic sensors (Sensits) were used to time-resolve the CSC sand mass to estimate hourly sand flux rates, and a perimeter tapered element oscillating microbalance (TEOM) monitor measured hourly PM10 concentrations. Hourly sand flux rates were related by dispersion modeling to hourly PM10 concentrations to back-calculate the ratio of vertical PM10 flux to horizontal sand flux (K-factors). Geometric mean K-factor values (K(f)) were found to change seasonally, ranging from 1.3 x 10(-5) to 5.1 x 10(-5) for sand flux measured at 15 cm above the surface (q15). Hourly PM10 emissions, F, were calculated by applying seasonal K-factors to sand flux measurements (F = K(f) x q15). The maximum hourly PM10 emission rate from the study area was 76 g/m2 x hr (10-m wind speed = 23.5 m/sec). Maximum daily PM10 emissions were estimated at 450 g/m2 x day, and annual emissions at 1095 g/m2 x yr. Hourly PM10 emissions were used by the U.S. Environmental Protection Agency (EPA) guideline AERMOD dispersion model to estimate downwind ambient impacts. Model predictions compared well with monitor concentrations, with hourly PM10 ranging from 16 to over 60,000 microg/m3 (slope = 0.89, R2 = 0.77).     

Two‐dimensional transport of lactate‐modified nanoscale iron particles in porous media

This study investigates the two‐dimensional transport of nanoscale iron particles (NIP) and lactate‐modified NIP (LMNIP) in homogeneous and heterogeneous porous media under typical pressurized groundwater flow conditions. A two‐dimensional bench‐scale test setup was developed and a series of experiments was conducted simulating homogeneous sand profile and two‐layer profile with two different sands. NIP and LMNIP at a concentration of 4 g/L were prepared in electrolyte simulating groundwater conditions and were injected at the inlet of the test setup under different pressure gradients (0.5. 0.8, 1, and 2 pounds per square inch). During the testing, effluent was collected and its volume and nanoiron concentrations were measured. At the end of the testing, soil cores were obtained at different distances from the inlet and were used to measure nanoiron concentrations and magnetic susceptibility values. Results showed that the transport of NIP and LMNIP was enhanced by increased pressure gradient. LMNIP transport occurred more uniformly as compared to bare NIP. The iron concentrations decreased with distance from the inlet to the outlet and increased from the top to the bottom of the test cell. The data indicate that, as the particles were transported, they underwent aggregation and sedimentation, which resulted in the observed non‐uniform spatial distribution of iron. The NIP and LMNIP transported through the high‐porosity and high‐permeability soil layer in the heterogeneous soil profile, implying that the transport occurred predominantly along the path of least resistance for the flow. Magnetic susceptibility values are found to have good correlation with the iron content in the soil and are helpful to characterize the transport of NIP and LMNIP. Overall, this study shows that the non‐uniform distribution of NIP and LMNIP occurs under two‐dimensional transport conditions and the soil heterogeneities can significantly impact the transport of NIP and LMNIP. The design of field delivery systems should consider such conditions and optimize the pressurized injection systems. © 2011 Wiley Periodicals, Inc.     

Magnitude and distribution of option value for the Washakie Wilderness,northwest Wyoming,USA

Option value is estimated for the Washakie Wilderness, northwest Wyoming, USA, using the contingent valuation technique. Consumer surplus, the traditional measure of economic value, is estimated separately and compared with option value. Several populations are tested, including Washakie visitors, Yellowstone National Park visitors, and residents from four metropolitan test markets: Salt Lake City, Utah; Portland, Oregon; Nashville, Tennessee; and Orlando, Florida, USA. The average annual preservation option value (consumer surplus) expressed by on-site wilderness visitors is $46.17 ($80.13), by urban residents is $9.70 ($8.97), and by rural residents is $8.43 ($7.80). Four selected attributes are determined to be important in motivating option demand for the Washakie, including existence value, bequest value, the desire for an on-site visit, and interest in securing the visiting privileges of others. The results suggest that option value is important in wilderness valuation and that off-site users account for a large part of the economic value of wilderness.     

Environmental site assessments and audits: Building inspection requirements

Environmental site assessment criteria were originally developed by organizations that focused, almost exclusively, on surface, subsurface, and pollution source contamination. Many of the hazards associated with indoor environments and building structures were traditionally not considered when evaluating sources and entities of environmental pollution. Since a large number of building materials are potentially hazardous, careful evaluation is necessary. Until recently, little information on building inspection requirements of environmental problems has been published. Traditionally, asbestos has been the main component of concern. The ever-changing environmental standards have dramatically expanded the scope of building surveys. Indoor environmental concerns, for example, currently include formaldehyde, lead-based paint, polychlorinated biphenyls, radon, and indoor air pollution. Environmental regulations are being expanded and developed that specifically include building structures. These regulatory standards are being triggered by an increased awareness of health effects from indoor exposure, fires, spills, and other accidents that have resulted in injury, death, and financial loss. This article discusses various aspects of assessments for building structures.